ошибка 10-706-00 . ксерокс 470ый не работает

[serjorossi]

ошибка 10-706-00 . ксерокс 470ый не работает

что делать ?

[Som]

Стучись к lyka

[Alex Gr]

Вот что в сервис мануале написано:

Description
(27Jun2002)

For information on the operation of the Exit Decurler ( TAG 279), select More Information.

The Decurler does not match the expected configuration or is malfunctioning.

Automatic configuration has detected an incorrect Decurler configuration.

One of the following messages are displayed on the User Interface in the Printer Status screen:

Not Ready - Configuration Mismatch exists.

Automatic Configuration detected an unrecoverable hardware problem.

or

Printer Fault - Please call for assistance

Procedure
This is an On-Site service call.
Yes No Unanswered

Go to the 10-706 Remote Diagnostic Procedure.

Go to the 10-706 On-Site Diagnostic Procedure.


10-706 Remote Diagnostic Procedure
The problem cannot be remotely diagnosed to one spare part. Following is the list of suspects.

Decurler Cam Drive Belt .

IIOC PWB W21A1 (Machine does not pass self test) PL 1.6 Item 1.

Decurler PL 6.1D.

Decurler Home Sensor PL 6.1D.

Decurler Position Sensor PL 6.1D

Send service and use the 10-706 On-Site Diagnostic Procedure to diagnose the problem.

10-706 On-Site Diagnostic Procedure
An Exit Decurler is installed.
Yes No Unanswered

Select [NVM] [NVM Tool] [Mark Service] [<All>]. Ensure the value in location 529, Exit Decurler Config Type, is set to ‘0’. Enter [NVM tab , NVM Tool].

Check the Decurler Configuration.

The Decurler configuration is valid for the output device installed. Refer to Table 1.
Yes No Unanswered

Ensure a valid Decurler is installed.

Select [NVM] [NVM Tool] [Mark Service] [<All>]. Check the value in location 529 Exit Decurler Config Type. Refer to Table 1. Enter [NVM tab , NVM Tool].

The NVM value is correct for the Decurler configuration installed.
Yes No Unanswered

In NVM Tool enter the correct NVM value in location 529.

In Component Control, select [IOT Paper Path], [Decurler cam Motor/ Clutch], then [CycleOutput].

Enter [Copier Sys tab , Component Control].

Observe the Decurler Cam Drive Motor. The Decurler Cam Drive Motor energizes in Component Control.
Yes No Unanswered

Switch the power [Off] and undock the Finisher.

Go to Flag 4. Check the circuit of the Decurler Cam Drive Motor for an open circuit.

Repair the wiring or replace the defective component:

Decurler PL 6.1D.

IIOC PWB W21A1 PL 1.6 Item 1.

Switch the power [Off] and undock the Finisher.

Check the following on the Decurler:

The drive gear on the Decurler Cam Drive Motor for damage.

The Decurler Cam Drive Belt for damage.

The Decurler cam drive components are free from damage:
Yes No Unanswered

Replace the Decurler Cam Drive Motor, or the Decurler, PL 6.1D, as required.

Check the position of the Decurler Position Sensor.

The sensor is in the correct position.
Yes No Unanswered

Reseat the Decurler Position Sensor in the correct position.

If the sensor cannot be reseated due to a broken mount, replace the Decurler Position Sensor PL 6.1D.

In Component Control, select [IOT Paper Path], [Decurler Position Sensor], then [Monitor Input].

Enter [Copier Sys tab , Component Control].

The display indicates the state of the sensor changed.
Yes No Unanswered

Go to Flag 3. Check the circuit of the Decurler Position Sensor for a short circuit or an open circuit.

Repair the wiring or replace the defective component:

Decurler Position Sensor PL 6.1D.

Decurler PL 6.1D.

IIOC PWB W21A1 PL 1.6 Item 1.

Check the position of the Decurler Home Sensor.

The sensor is in the correct position.
Yes No Unanswered

Reseat the Decurler Home Sensor in the correct position.

If the sensor cannot be reseated due to a broken mount, replace the Decurler Home Sensor.

Go to Flag 1. Check the circuit of the Decurler Home Sensor for a short circuit or an open circuit.

Repair the wiring or replace the defective component:

Decurler Home Sensor PL 6.1D.

Decurler PL 6.1D.

IIOC PWB W21A1 PL 1.6 Item 1.

Figure 1 10-706 RAP Circuit Diagram

Figure 2 Decurler Component Locations